Spyderco Manix 2 G10 XL Custom Titanium Screw Set + Lanyard Tube - MATTE RAW

Regular price $145.00

Tax included.

View color chart

Also available in other custom anodized colors.  Just contact me if interested.


FREE WORLDWIDE DELIVERY INCLUDED !!!


Up for sale is a ...

Custom 10 Piece MATTE RAW Titanium Torx Screw
Set 
and Custom Titanium Lanyard Tube to fit:
Spyderco MANIX 2 & MANIX 2 XL (G10) Series Knives.



PLEASE NOTE: THIS SET ONLY FITS THE MANIX 2 THAT USES G10 SCALES.

(WILL NOT FIT THE MANIX 2 LIGHTWEIGHT VERSION)


The factory standard torx screws are not titanium.

They might get rounded, threaded or simply get lost over time. 

Upgrade the standard torx screws, to a set of rust proof Custom Titanium Torx Screws in MATTE RAW.

These Custom Titanium Torx screws are a direct replacement for the Spyderco Manix 2 knives.

These custom parts are not designed to fit Cloned or Fake Spyderco knives.
Do not buy these parts for any cloned or fake knives as they probably won't fit.


Please note:
 No knives mentioned or pictured are for sale.


What is included in this sale is only the 10 piece set of Titanium Screw and parts to fit the original
Spyderco Manix 2 knife.
 Consisting of only 10 x MATTE RAW parts in total. 


This 10 Piece set includes the following titanium screws:

2 x T10 Torx MATTE RAW Titanium Pivot Screws
4 x T8 Torx 
MATTE RAW Titanium Body Screws
3 x T6 Torx MATTE RAW Titanium Pocket Clip Screws
1 x Custom 
MATTE RAW Titanium xxxadrenalinxxx design Lanyard Tube


Custom Sized Lanyard Hole (smaller):

I have designed this Titanium Lanyard Tube to have a smaller hole with a Ø 4.5mm / 3/16 inch diameter hole.

This makes the fitment of 550 Paracord a nicer tighter fit. Without it being overly loose like the original MANIX 2 hole.

When installed it will also show more of the MATTE RAW Titanium Lanyard Tube flange from the side view.

The smaller lanyard hole is designed to still fit normal (4mm) 7 Strand 550 Paracord. (as seen in my PM2 tube photos).

For reference the Original Manix 2 Steel Lanyard Hole is a Ø 6mm / 1/4 Inch Diameter Hole.



LANYARD TUBE INSTALLATION WARNING: (MUST READ)

I NEVER INTENDED TO DESIGN THIS ITEM. DUE TO THE FACT THAT YOU CAN POSSIBLY DAMAGE
YOUR KNIFE IN THE PROCESS OF TAKING APART AND INSTALLING ONE OF THESE LANYARD TUBES.

HOWEVER DUE TO THE MANY REQUESTS TO MAKE SOME.  HERE IT IS....

PLEASE WATCH THE MANY YOUTUBE VIDEOS AVAILABLE ON DISASSEMBLY & INSTALLATION FIRST.
YOU WILL HAVE TO FULLY DISASSEMBLE YOUR KNIFE TO INSTALL THIS LANYARD TUBE.


THE ORIGINAL MANIX 2 LANYARD TUBE IS PRESSED AND FLARED IN PLACE AND CAN BE VERY DIFFICULT TO REMOVE.

BY PURCHASING THIS ITEM YOU ARE FULLY AWARE THAT POSSIBLE IRREVERSIBLE DAMAGE
COULD OCCUR AS A RESULT OF TAKING
 THE ORIGINAL TUBE OUT.

YOU
 ALONE WILL BE TAKING FULL RESPONSIBLY FOR ANY SUCH DAMAGE.

(THE SPYDERCO WARRANTY DOES NOT COVER THESE TYPES OF MODIFICATIONS)


IF YOU ARE NOT CONFIDENT IN TAKING APART AND POSSIBLY HAVING TO MODIFY
YOUR KNIFE TO FIT (IF ANYTHING GOES WRONG). IT IS BEST NOT TO BUY THIS ITEM.



Screw Installation Notes:

The Manix 2 knife can be quite tricky to take apart and put together compared to other knives.
Even tuning the tightness of the Manix 2 body screws can effect the pivot opening performance.

The original Manix 2 screws can be quite hard to remove. Please watch some youtube videos
beforehand to see how it is done. The factory loctite thread glue can make the screws hard to
get out too causing the Torx head to strip. 
Please use some Good strong quality Torx tools to
(Such as Wiha Torx tools)
. T6, T8, T10 in size.

Titanium Screws: My titanium screws are designed for a precise fit with the standard scales
and with the stock factory internal threaded hardware. All the internal factory hardware needs
to be CLEAN of any old thread locking glue as this will cause fitment problems. Clean by
soaking the stock metal hardware in Acetone until it can be removed. Remove the thread
locking glue with the stock steel screws. DO NOT use these titanium parts to clean out the
factory threads.


Please do not purchase this set if you are not confident in taking your Manix apart and putting it back together.




MARCH 2020 UPDATE:

RE-DESIGNED THE POCKET CLIP SCREWS.

THEY ARE NOW SLIGHTLY LONGER THAN THE STOCK ONES.

SO IT CAN BE USED WITH BOTH STOCK AND THICKER AFTERMARKET DEEP CARRY POCKET CLIPS.

WHEN USING WITH THE STOCK POCKET CLIP IT WILL POKE OUT OF THE LINERS A TINY BIT.

NOT ENOUGH TO HIT THE BLADE THOUGH. MOST PEOPLE ARE UPGRADING THEIR POCKET CLIPS

SO THIS IS WHY THE IT HAS NOW BEEN MADE LONGER OTHERWISE THE STOCK ONES ARE TOO SHORT.


DECEMBER 2018 UPDATE:

WAS OUT OF STOCK DUE TO SELLING OUT.

THEN DECIDED TO RE-DESIGN THE SET AGAIN TO BE STRONGER.

POCKET CLIP SCREWS ARE NOW UPGRADED AND NOW STRONGER!!!

Many wasted parts, lots of wasted tooling, much headaches.

These custom Spyderco parts have taken around 7 Generations and at least 4 years to get it to this stage.


JULY 2018 UPDATE:

WAS OUT OF STOCK DUE TO BEING RE-DESIGNED.

PIVOT SCREWS ARE NOW STRONGER!!!

Many wasted parts, lots of wasted tooling, much headaches.

These custom Spyderco parts have taken around 6 Generations and at least 3+ years to get it to this stage.



Previous updates...below.

Please note: These custom screws were extremely hard to make.
It took many production runs and a very long time to get it to this stage.
This is as good as I can get it, as it is very hard to hold when machining
because of the thin angled edge on the countersunk screw head.
Please be aware that the screw's head may stick out from the scale
by a very, very tiny little amount. As shown in the ebay photos attached.
The G10 scale can be possibly countersunk a little be more to fix this.
However by purchasing this set you are aware of this. (2018 UPDATE = NOW FIXED)

2018 UPDATE: These are now perfect!!!
Many wasted parts, lots of wasted tooling, much headaches.
It has taken around 5 Generations and at least 3 years to get it to this stage.

2017 UPDATE: These screws were machined to fit perfectly with every allowable tolerance however it was a bit too thin
and caused it to break when torqued down hard. Had to scrap them and re-design. 
(2018 UPDATE = NOW FIXED)

2016 UPDATE: The scale screw's Torx drive head wasn't machined well.
Which was very hard to do on such a small thin countersunk head = looked crap. 
(2018 UPDATE = NOW FIXED)

2015 UPDATE: So many trial runs and bad batches. (didn't even list it up on ebay).
Many issues to sort out. 
(2018 UPDATE = NOW FIXED)

2014 UPDATE: Too many issues to list and remember.
Much wasted $$$$$ on tooling that didn't work. 
(2018 UPDATE = NOW FIXED)



Other Notes:

Slight color and machining variations may also occur between batches. Custom colors can be requested.
Other colors such as: purpleyellowCoppermaroonraw titaniumlight bluebrassdark bluebronzegold etc.

Once you have received a colored titanium item. It may appear to have lost color once touched,
this is just the oil from your hands. If the oil been cleaned off the color will come back. See cleaning tip below.


Terms and Conditions for International Orders:

If your country's language is one other than English. You will need to confirm that you understand, NO KNIVES ARE FOR SALE.

International orders are sent via Airmail and usually take around 2 or 3 weeks to arrive to you.
However orders can take longer to arrive depending on your country's air mailing delivery system.
Please do not buy if you cannot agree to this. All International items are sent via Airmail with tracking.


Sorry I have to keep repeating myself but there are many buyers especially from non English speaking countries that
assume the knife is also included. I am just trying to make my listing as clear as possible that NO KNIVES ARE INCLUDED.
Sorry no orders from Russia will be accepted. Orders from Italy must supply a phone number to add to the parcel and customs forms.



WORLDWIDE POSTAGE IS FREE !!!




I have more matching MATTE RAW Spyderco Manix 2 titanium parts available.
Such as: Pocket Clip Hole Protector Screws or sets in other colors etc.
Please check my other listings or contact me for more options.


(This set is also available in other colors: Brass/Bronze/Purple/Blue/Raw etc. Please contact me if interested).


Anodized Titanium Cleaning Tip:

To maintain the look of your new titanium parts.

Wipe clean with some Acetone but at the same time

be careful NOT to get Acetone on the G10 or Carbon knife scales.

(Windex can also work too as a safer option)


(WILL NOT FIT THE MANIX 2 LIGHTWEIGHT VERSION)