Spyderco Paramilitary PM2 Custom Titanium 3pc Pocket Clip Screw Set - MATT GREEN

Regular price $32.49

Tax included.


Also available in other custom anodized colors.  Just contact me if interested.


FREE WORLDWIDE DELIVERY INCLUDED !!!

Up for sale is a ...

Custom Machined 3 Piece Titanium Pocket Clip Screw Set
(with a bead blasted non-reflective matt finish)

Anodized in
GREEN to fit to fit Spyderco Paramilitary 2 (PM2) Knives.


The factory standard torx screws are not titanium.

They might get rounded, threaded or simply get lost over time. 

Upgrade the standard torx screws, to a set of rust proof Custom Designed Titanium Torx Screws anodized in MATT GREEN.


These Custom Designed Titanium Torx screws are a direct replacement for the
Spyderco PM2 knives.


Please note:
No knives pictured or mentioned are for sale.


What is included in this sale is only the 3 piece set of Titanium Screws to fit the original
Spyderco PM2 knife.
Consisting of only 3 x MATT GREEN Anodized screws in total. 



This 3 Piece set includes the following titanium screws:

3 x T6 Torx MATT GREEN Anodized Titanium Anodized Pocket Clip Screws



Anodizing Notes:


Green is the hardest color to anodize, this color can vary on single parts to full sets from a Blue Green to a Yellow Green color.
I will try my best to keep the color as consistent as possible. (often re-doing it a few times, wasting parts or throwing away parts in the process)
The Matt Finish is also very hard to do and may not reach all the way inside the torx drive holes or only on some of them. (As seen in the photos)
Matt Green is also very hard to capture on a photograph as it's true color may look different under different lighting conditions or on different angles.

or even on different screens when being viewed.
Additional PM2 parts: If wanting the Full Parts Set (screw set / standoff / pin / lanyard tube) best to
order all the PM2 parts at the same time so it will be in the same anodizing batch and match much better than if ordered at a later date.


Machining Notes:

Machining variations may also occur between batches. As I am always trying to improve my parts, so slight improvements or upgraded design elements may be added at different times along the way. This may not be reflected in the photos. However it will be added to the notes seen below.


* By placing an order for this 9pc Set you are accepting there could be a variation in color or machining to what is pictured.



Notes about the 9pc Screw set development which includes the pocket clips screw notes too.


DECEMBER 2018 UPDATE:


WAS OUT OF STOCK DUE TO SELLING OUT.

THEN DECIDED TO RE-DESIGN THE SET AGAIN TO BE STRONGER.

POCKET CLIP SCREWS ARE NOW UPGRADED AND NOW STRONGER!!!

Many wasted parts, lots of wasted tooling, much headaches.

It has taken around 7 Generations and at least 4 years to get it to this stage.

JULY 2018 UPDATE:

WAS OUT OF STOCK DUE TO BEING RE-DESIGNED.

PIVOT SCREWS ARE NOW STRONGER!!!

Many wasted parts, lots of wasted tooling, much headaches.

It has taken around 6 Generations and at least 3+ years to get it to this stage.


Previous updates...below.

Please note: These custom screws were extremely hard to make.
It took many production runs and a very long time to get it to this stage.
This is as good as I can get it, as it is very hard to hold when machining
because of the thin angled edge on the countersunk screw head.
Please be aware that the screw's head may stick out from the scale
by a very, very tiny little amount. As shown in the ebay photos attached.
The G10 scale can be possibly countersunk a little be more to fix this.
However by purchasing this set you are aware of this. (2018 UPDATE = NOW FIXED)

2018 UPDATE: These are now perfect!!!
Many wasted parts, lots of wasted tooling, much headaches.
It has taken around 5 Generations and at least 3 years to get it to this stage.

2017 UPDATE: These screws were machined to fit perfectly with every allowable tolerance however it was a bit too thin
and caused it to break when torqued down hard. Had to scrap them and re-design.
(2018 UPDATE = NOW FIXED)

2016 UPDATE: The scale screw's Torx drive head wasn't machined well.
Which was very hard to do on such a small thin countersunk head = looked crap.
(2018 UPDATE = NOW FIXED)

2015 UPDATE: So many trial runs and bad batches. (didn't even list it up on ebay).
Many issues to sort out.
(2018 UPDATE = NOW FIXED)

2014 UPDATE: Too many issues to list and remember.
Much wasted $$$$$ on tooling that didn't work.
(2018 UPDATE = NOW FIXED)


Installation Notes:

The PM2 knife can be quite tricky to take apart and put together compared to other knives.
Please do not purchase this set if you are not confident in taking your PM2 apart and putting it back together.
Even tuning the tightness of the PM2 body screws can effect the pivot opening performance.


The original PM2 screws can be quite hard to remove. Please watch some youtube videos beforehand to
see how it is done. The factory loctite thread glue can make the screws hard to get out too causing the Torx head to strip.
Before installation of these titanium screws. Please clean and remove all existing factory loctite glue.

Also use some Good strong quality Torx tools to (Such as Wiha Torx tools).


Other Notes:

Slight color and machining variations may also occur between batches. Custom colors can be requested.
Other colors such as: purple, yellow, maroon, raw titanium, light blue, brass, dark blue, bronze, gold etc.

Once you have received a colored titanium item. It may appear to have lost color once touched,
this is just the oil from your hands. If the oil been cleaned off the color will come back. See cleaning tip below.


Terms and Conditions for International Orders:

If your country's language is one other than English. You will need to confirm that you understand, NO KNIVES ARE FOR SALE.

International orders are sent via Airmail and usually take around 2 or 3 weeks to arrive to you.
However orders can take  to longer to arrive depending on your country's air mailing delivery system.
Please do not buy if you cannot agree to this. All International items are sent via Airmail with tracking.


Sorry I have to keep repeating myself but there are many buyers especially from non English speaking countries that
assume the knife is also included. I am just trying to make my listing as clear as possible that NO KNIVES ARE INCLUDED.
Sorry no orders from Russia will be accepted. Orders from Italy must supply a phone number to add to the parcel and customs forms.



WORLDWIDE POSTAGE IS FREE !!!




I have more matching MATT GREEN Spyderco PM2 titanium parts available.
Such as: Full Screw Set, Lanyard Tubes, Standoffs, Pins, Pocket Clip Screws etc.
Please check my other listings or contact me for more options.


(This set is also available in other colors: Brass/Bronze/Purple/Blue/Raw etc. Please contact me if interested).


Anodized Titanium Cleaning Tip:

To maintain the look of your new titanium parts.

Wipe clean with some Acetone but at the same time

be careful NOT to get Acetone on the G10 or Carbon knife scales.

(Windex can also work too as a safer option)



PLEASE NOTE: These custom parts may need up to 1 week lead time to process after ordering.